Cedar Hill Electrical Company handles residential and commercial electrical work across Cedar Hill and the surrounding Dallas County area. Repairs, panel upgrades, new wiring, EV charger circuits, generator hookups: the full range of electrical work for homes and businesses. When something goes wrong with the power, or when a property needs new electrical capacity, this is the number to call. We take urgent repair calls and short-notice work, and we are available every day from 7:00 AM to 9:00 PM.
We get to the bottom of the problem fast.
Keeping a home safe starts with the wiring behind the walls, and most electrical problems show up in ways that are hard to ignore: a dead outlet in the kitchen, lights that flicker when the HVAC kicks on, a breaker that trips every time you run two appliances at once, or a burning smell coming from a switch plate. These are not problems to put off.
When we respond to a repair call, the first step is a thorough look at what is actually happening. That means checking the outlet, the circuit, the panel, and the wiring path to find where the fault is. We look for overloaded circuits, failed GFCI or AFCI protection, loose connections at the panel, and wiring that has degraded over time. The scope of the problem gets explained before any work starts, and the price is confirmed before we proceed.
We offer prompt response, even for last-minute electrical calls, because an electrical fault that is left alone rarely stays the same size.
A burning smell near an outlet or switch usually points to a connection that is overheating. Sparks from a receptacle can mean arcing at the contact points inside. A breaker that trips repeatedly on the same circuit is telling you that circuit is carrying more load than it was wired for, or that something downstream has failed. None of these symptoms are emergencies in the dramatic sense, but all of them deserve attention before they become worse. We walk through what we find, explain what it means in plain terms, and confirm the repair plan before touching anything.
Your time matters, so we keep the wiring job moving, and that starts with an honest assessment of whether the panel can carry the load. A lot of homes in the Cedar Hill area were built with panels that made sense for the electrical demand of the time. Add a home office, a Level 2 EV charger, a new dryer circuit, or a kitchen remodel, and that original panel may no longer have the capacity to handle the load safely.
Panel replacement and 200-amp service upgrades are among the most common jobs we handle. The work involves removing the old equipment, installing a new main breaker panel with the correct amperage rating, and reconnecting the branch circuits with proper labeling and load distribution. Where the service entrance or meter base needs attention as part of the upgrade, that gets addressed in the same scope. Subpanel installation for a detached garage, workshop, or addition follows the same process: load calculation first, then the right equipment for the job.
We carry out electrical work done to the standard the next inspection expects, which means the panel work is done to current code and ready for the inspector when the permit requires it.
From a single GFCI outlet to a whole-home rewire, the first step is the same: understand what the property needs and confirm the scope before scheduling. Wiring work covers a wide range, and the right approach depends on what is already in the walls.
Older homes sometimes have knob-and-tube wiring or aluminum branch circuit wiring, both of which present specific challenges. Knob-and-tube has no ground conductor and was not designed for modern loads. Aluminum wiring at the receptacle level requires proper connectors and terminations to reduce the risk of overheating at connection points. We handle both: full rewiring where the scope calls for it, and targeted remediation where that is the better fit.
Outlet and switch work includes GFCI and AFCI receptacles, USB outlets, dimmer switches, outdoor and weatherproof receptacles, and switch replacements. Lighting installation covers recessed and LED lighting throughout the home, indoor and outdoor fixtures, security and motion-sensor lights, and landscape lighting. Ceiling fan installation and wiring is part of the same category: a straightforward job when the box and circuit are in good shape, and a more involved one when they are not.
The wiring done properly, start to finish, means every connection is checked, every circuit is tested, and the work is left clean.
Straight answers on the phone. Real electrical work. Quick to respond.
Kitchen and bathroom remodels, home additions, garage wiring, and workshop circuits all create new electrical demand that the existing system may not be set up to handle. A kitchen remodel typically requires dedicated circuits for the refrigerator, dishwasher, microwave, and countertop receptacles. A bathroom remodel calls for GFCI protection at every receptacle and proper wiring for exhaust fan circuits. Under-cabinet lighting, recessed lighting in a new ceiling, and dedicated circuits for a dryer or range are all part of remodel electrical work we handle regularly.
When a home addition goes up, the panel needs to be evaluated for available capacity before the new circuits are roughed in. We scope that as part of the job so there are no gaps between the addition and the electrical supply it needs.
Scheduling a service call is simple, and it starts with a conversation about what the property needs. For EV charger installation, that conversation covers the panel first. A Level 2 charger draws a dedicated 240-volt circuit, and the panel has to have the capacity to carry it. We check the available breaker slots, the current load, and the service entrance amperage before confirming what the installation involves. If a panel upgrade is needed first, that gets scoped and priced as part of the same project.
Whole-home surge protection is installed at the panel and covers the circuits that feed sensitive equipment throughout the house: electronics, appliances, HVAC systems, and anything else that a voltage spike can damage. In the Dallas area, where summer storms can push significant electrical surges through the utility lines, a surge protection device at the panel is a straightforward way to protect what is plugged in.
Backup generator hookup and transfer switch installation covers the connection between the generator and the home's electrical system. A properly installed transfer switch isolates the home from the utility grid when the generator is running, which is both a code requirement and a safety requirement. We handle the transfer switch, the wiring to the panel, and the connection to the generator inlet.
When you call us, you get a straight answer about the work.
Office buildings, retail spaces, restaurants, and light commercial properties all have electrical needs that go beyond what a standard residential service call covers. We work with property managers and business owners on commercial panel upgrades, dedicated circuits for commercial equipment, outlet and lighting installation in commercial spaces, and electrical safety inspections.
An electrical safety inspection for a commercial property covers the panel, the branch circuits, the receptacles, the grounding system, and the visible wiring. It is a useful step before a lease renewal, a sale, or a renovation, and it gives a property manager a clear picture of what the electrical system looks like and what, if anything, needs attention.
Commercial repair work follows the same process as residential: diagnose the fault, explain what is involved, confirm the price, and carry out the work. Give us a call and consider it handled.
From a single GFCI outlet to a whole-home rewire, the first step is the same, and that step is the phone call. When you call to describe the job, we ask the questions that let us scope the work: what the symptom is, what type of property it is, what the panel situation looks like, and whether there are any access or timing constraints. From that conversation, we give you a rate before anything is scheduled.
The price you get on the call covers what was scoped. If the job turns out to involve something additional once work is underway, that gets communicated before it is added. You are not left to find out at the end what the bill covers. Ask what the quote includes and you get a clear answer.
We are available every day from 7:00 AM to 9:00 PM. When you call, we confirm what the schedule has open and how soon work can start. We're one phone call from getting your power right.
We handle electrical work in Cedar Hill and throughout the surrounding area. The communities we serve regularly include Duncanville, DeSoto, Lancaster, Midlothian, Mansfield, and Grand Prairie, along with other neighborhoods across Dallas County. Both residential and commercial properties are covered across this area.
If you are outside Cedar Hill but nearby, call and ask about availability at your address.
Yes. We handle electrical work across Cedar Hill and throughout the surrounding area, including Duncanville, DeSoto, Lancaster, Glenn Heights, Grand Prairie, Midlothian, Mansfield, and Waxahachie. Knowing the housing stock in this area, including the mix of older established neighborhoods and newer residential construction, helps us scope jobs accurately on the call.
When you call, a real person answers. That person knows the trade and can scope the job on the phone: asking the right questions about the symptom, the panel, and the property so you get a price before anything is booked. You are not navigating a menu or waiting on a callback.
Ask what the visit covers, what the price includes, and whether there are any conditions that could change the scope once the work starts. We answer all of those on the call. You should also confirm availability at your address if you are outside Cedar Hill proper, since we cover a wide area across Dallas County and into Ellis County.
Call us at (945) 375-7193 and describe what you are seeing.
We will work through what happened and get back out to address it. The goal is electrical work done to the standard the next inspection expects, and that means standing behind what we do.
The wiring path, the age of the panel, and the condition of the branch circuits all affect what a repair involves. A tripping breaker in a newer home with a modern panel is a different job than the same symptom in a home with a 100-amp fuse box and aluminum wiring. We explain what we find and why the approach fits the specific property.
Opening a wall or ceiling sometimes reveals wiring that is in worse condition than the symptom suggested, or a panel that needs attention before the new circuit can be added safely. We communicate anything unexpected before continuing, so you are never surprised by a scope change. The job takes as long as it actually takes to do it correctly.
We serve Cedar Hill and the communities around it, including Duncanville, DeSoto, Lancaster, Glenn Heights, Grand Prairie, Midlothian, Mansfield, and Waxahachie, along with other neighborhoods across Dallas County and into northern Ellis County. If you are unsure whether we cover your address, call and we will confirm.
Simple scheduling. Pricing agreed up front. Power back fast.
Cedar Hill Electrical Company is available every day from 7:00 AM to 9:00 PM for electrical repairs, panel upgrades, wiring, EV charger circuits, generator hookups, and everything in between. The rate is confirmed on the call before anything is booked.
Ready to get the power back on?
Call (945) 375-7193 to describe the job and get a price.
(945) 375-7193